Venus Domestic VDH 200 Manual de usuario

& GUARANTEE CARDHeat Pump Water Heater -DomesticRUser Manual

9R2. Each part connected to unit needs to be connected with method of loose joint andinstalled with intermediate valve.3. Ensure that all plum

10R Power supply1. If the supply voltage is too low or too high, it can cause damage and/or result in unstableoperation of the heat pump

11RFactory Default SettingDescription Switch1 Switch2 Switch31 phase, Domestic airto water heat pumpwater heater, CycleheatingON ON ONElectrical Wirin

12R Section 3Operating Heat PumpLCD User-Friendly Interface ControllerGeneral instruction The control panel applies to a single system single p

13RKeys explanation:Unlocking Keys: Press the “power” key for 3 seconds until you hear an audible tone, thenrelease the key. The back light of the LCD

14RThe inquiry codes are from A1 to Er. By pressing the “setting” key sequentially, thedesired inquiry code will be selected and value displayed.

Rthe compressor when to re-start until desired temperature is reached. (3~18°C(37.4~64.4°F) default: 5°C (37.4°F)). For example, set water temp. = 25

16RHeat pump ON/OFF timers: 01—ON/OFF timing02—ON/OFF timing Press the “timer” key and enter timer 01 ON time. Set the ON time as in Clock Settingsect

17Rof the heat pump on a monthly basis by monthly password control. For example: If thereis an agreement which involves monthly installment, the insta

18RREMEMBER: All preset settings is reverted back to the original factory defaultsettings. The password function will be disabled (C1=01, C2=01,

1RDear Customer,Thank you for purchasing Venus Heat Pump Water Heater. We have enclosed this handy installation manual to help you correctly ins

18RREMEMBER: All preset settings is reverted back to the original factory defaultsettings. The password function will be disabled (C1=01, C2=01,

20RSection 4General MaintenanceController Error CodesThe following Common Error Codes for the heat pump units will be displaye

21R7. Keep inspecting power and electrical components’ wiring to make sure their normaloperation. 8. All the safety protection devices have been

21R7. Keep inspecting power and electrical components’ wiring to make sure their normaloperation. 8. All the safety protection devices have been

21R7. Keep inspecting power and electrical components’ wiring to make sure their normaloperation. 8. All the safety protection devices have been

22RProblems and Corrective ActionNO.ProblemDescriptionPossible Cause Corrective Action1Error code05E1. Measured Pool Temp <Actual Pool Tempa) The p

R8Error code18E1. Compressor discharge temperaturesensor faulty or damaged.Replace the compressor discharge temperaturesensor.2. Compressor discharge

24R12 Slowincrease ofwatertemperature1. Insufficient refrigerant.1. Check for leakages, if found, repair and re-chargerefrigerant as per volume specif

25Rb) The main powersupply voltage is lowerthan 175V.Check and ensure that themains power supply cable',length and thickness, iswithin the specif

26RITEM DISCRIPTION QTY ITEM DISCRIPTION QTY1 Base Plate 1 10 4’’ Stop Valve 12 Compressor, Rotary 1 11 Small Fixing Plate 13 Evaporator 1 12 Electro

2RSection 1IntroductionProduct Overview General Features1. Using heat energy from ambient air and reproduces more heat energy, savi

Dealer's Name and Address : Dealer's SignatureVenus Heat Pump Water Heater & Tank are covered by warranty for

SERVICE LOGDateDescription complaintof Within Warranty.OutsideWarranty.SignatureWarranty

If you have any questions, problem or requierments of spare parts, get in touch with us for immediate attention atThe Customer Care CellVenus Home Ap

3RSection 2InstallationThe following general information describes how to install the domestic Heat pump water heater.Note: Before insta

4RDomestic Heat Pump Water Heater SpecificationAmbientInlet/OutletØ Ø Ø Ø1250

5R5. Adequate water flow. This manual provides the information needed to meet these requirements.Installation LocationCAUTION!1. DO

6RInstallation details All criteria given in the following sections reflect minimum clearances. However, eachinstallation must a

R5. For the units which installed at the rack on the outer wall, the rack should be fixed withwall-bolts. And the heat pump must be installed

8RFigure 2The heat pump must be protected from Reverse flow of water. If there is any chance provide a check valve between the water tank and the col